Hougen vs EUROBOOR: Drill Presses Compared by Specs
As an Amazon Associate we earn from qualifying purchases. Links on this page are affiliate links.
This hougen vs EUROBOOR drill press comparison looks at two magnetic drilling machines. Both units are magnetic configurations designed for steel work. They differ in key areas like capacity and safety features. The Hougen HMD900 offers a larger hole capacity. The EUROBOOR ECO.36+ focuses on low profile design and advanced safety. You will see how these specs affect your workflow below.
Key differences
| Aspect | Hougen HMD900 Magnetic Drill | EUROBOOR Low Profile Magnetic Drill Press |
|---|---|---|
| Hole Capacity | 1.5" | 1-7/16" |
| Voltage | 115V | not listed |
| Motor Power | not listed | 9.5A |
| Spindle Speed | not listed | 700 RPM |
| Magnetic Force | not listed | 2645 lbs |
| Height | 15 inches | 6 1/2 inches |
Which one should you choose?
Choose Hougen HMD900 Magnetic Drill if
- You need to drill holes up to 1.5 inches in diameter.
- You require a standard 115V power connection.
- You prefer a unit with a slot drive arbor for quick accessory changes.
Choose EUROBOOR Low Profile Magnetic Drill Press if
- You are working in tight spaces with limited vertical clearance.
- You want automatic motor shut-off for enhanced safety.
- You need a powerful 9.5A motor with high magnetic holding force.
Verdict: Choose the Hougen HMD900 if your primary need is maximum hole capacity and standard voltage compatibility. Select the EUROBOOR ECO.36+ if you work in confined spaces or prioritize advanced safety features like gyro-technic shut-off. Your specific workspace constraints should drive this decision.
Hougen vs EUROBOOR Spec Comparison
Hole Capacity
The Hougen HMD900 provides a maximum hole capacity of 1.5 inches. This measurement indicates the largest diameter bit the machine can accept. The EUROBOOR ECO.36+ offers a range from 7/16 inch to 1-7/16 inches. The 1-7/16 inch limit is slightly smaller than the Hougen's 1.5 inch capacity. If you need to drill the absolute largest holes possible, the Hougen holds a slight advantage. The difference is minimal for most structural steel work. Both machines handle standard annular cutters well. You should check your specific bit requirements against these limits. The Hougen wins this round by a narrow margin due to its higher maximum diameter.
Magnetic Force
The EUROBOOR ECO.36+ specifies a magnetic holding force of 2645 lbs. This figure represents the pull strength against steel surfaces. The Hougen HMD900 data does not list a specific magnetic force rating. Without this number, you cannot verify if the Hougen meets or exceeds the EUROBOOR's holding power. A higher magnetic force generally allows for safer drilling in overhead or vertical positions. The EUROBOOR provides a clear specification here, which helps you assess stability. The Hougen may have comparable strength, but the lack of data makes it a tie. You rely on the EUROBOOR's stated 2645 lbs for certainty.
Spindle Speed
The EUROBOOR ECO.36+ operates at 700 RPM with no load. It drops to 400 RPM under a 9.5A load. The Hougen HMD900 data does not list spindle speed. Different materials require different speeds for optimal cutting. Steel usually benefits from lower RPMs for larger bits. The EUROBOOR provides these specific speed values, allowing you to match them to your workpiece. The Hougen's speed remains unknown from the provided data. You cannot compare performance without this key specification. The EUROBOOR offers transparency here, giving you better information for planning your drilling tasks. This is a clear advantage for the EUROBOOR.
Safety Features
The EUROBOOR ECO.36+ includes the GYRO-TEC automatic shut off. This feature stops the motor during sudden displacement, loss of magnetic force, or excessive vibration. It also has power fluctuation and surge protection. The Hougen HMD900 mentions increased safety and spring slug ejection. Slug ejection removes the drilled metal core automatically. However, the Hougen data lacks details on automatic shut off or electrical protection. The EUROBOOR provides a more comprehensive list of active safety systems. You get better protection against machine damage and operator injury with the EUROBOOR. The Hougen's features are less detailed in the provided specifications.
Design Profile
The EUROBOOR ECO.36+ is described as the lowest profile magnetic drill. It measures only 6.5 inches in height. This design is ideal for tight spaces like H-beams. The Hougen HMD900 measures 15 inches in height. This is significantly taller than the EUROBOOR. If you are working in confined areas, the EUROBOOR is the better choice. The Hougen is wider at 11 inches and deeper at 6.75 inches. The EUROBOOR is more compact vertically. You need to measure your workspace before choosing. The EUROBOOR wins this round due to its superior low-profile design for restricted environments.
Choose based on capacity and safety
You need the largest hole diameter
The Hougen HMD900 accepts a 1.5 inch hole capacity. This is larger than the EUROBOOR ECO.36+ maximum of 1-7/16 inches. If your projects require drilling larger diameters in steel, this unit provides the necessary range. The slot drive arbor also allows for quicker accessory changes.
You work in tight vertical spaces
The EUROBOOR ECO.36+ has a low profile design measuring only 6.5 inches in height. This makes it ideal for drilling in confined areas like H-beams or steel structures with limited clearance. The Hougen HMD900 is taller at 15 inches, which may not fit your specific workspace constraints.
You prioritize advanced safety features
The EUROBOOR ECO.36+ includes GYRO-TEC automatic shut off. This stops the motor during sudden displacement, loss of magnetic force, or excessive vibration. It also features power surge protection and a TempTec two-way magnet to reduce heat. The Hougen HMD900 lists spring slug ejection but lacks these specific electronic safeguards.
The products compared
Hougen HMD900 Magnetic Drill
Best for: Heavy steel drilling on vertical surfaces
- Hole Capacity
- 1.5"
- Voltage
- 115V
- Configuration
- Magnetic
- Dimensions
- 11 × 6.75 × 15 inches
- Weight
- 27 pounds
View on Amazon: Hougen HMD900 Magnetic Drill Affiliate link
The Hougen HMD900 is a 115V magnetic drill press designed for heavy-duty metalwork. It features a 1.5-inch hole capacity and a slot drive arbor for quick accessory changes. Weighing 27 pounds, it offers a 15-inch height and 11-inch length for stable mounting. The ergonomic housing and spring slug ejection improve safety and reduce maintenance. This unit suits users needing reliable, high-capacity drilling on vertical surfaces.
Pros
- 1.5-inch maximum hole capacity
- Slot drive arbor for faster accessory changes
- Spring slug ejection system
- Hidden motor cord for cleaner operation
Cons
- Limited to 1.5-inch hole capacity
- Fixed 115V voltage requirement
- No variable speed control listed
Good fit if
- You need to drill large holes in thick steel
- You require a magnetic base for vertical work
- You want quick accessory changes via slot drive
Skip if
- You need to drill holes larger than 1.5 inches
- You require a 230V power connection
- You need a lightweight portable unit under 20 pounds
Verdict: Hougen HMD900 Magnetic Drill delivers solid 1.5-inch capacity for industrial tasks. It fits professionals drilling thick metal on vertical surfaces who value magnetic stability and quick bit changes.
EUROBOOR Low Profile Magnetic Drill Press
Best for: Drilling under steel beams in tight spaces
- Motor Power
- 9.5A
- Spindle Speed
- 700 RPM (400 RPM under load)
- Hole Capacity
- 7/16" - 1-7/16"
- Magnetic Force
- 2645 lbs
- Configuration
- Magnetic
- Amperage
- 5 A
View on Amazon: EUROBOOR Low Profile Magnetic Drill Press Affiliate link
The EUROBOOR ECO.36+ is a low-profile magnetic drill press designed for tight spaces. It features a 9.5A motor and a 2645 lbs magnetic base. The unit drills holes from 7/16" to 1-7/16" at 700 RPM. Its 6.5" height fits under H-beams. You get automatic shut-off and power surge protection. This model suits steel structure work where clearance is limited.
Pros
- 2645 lbs magnetic holding force
- 6.5-inch low profile height
- 9.5A motor with 700 RPM speed
- Gyro-Tec automatic shut-off safety
- Drills up to 1-7/16" diameter
Cons
- Single speed operation limits versatility
- No variable speed control
- Limited to one speed setting
Good fit if
- You need to drill under steel beams
- You require strong magnetic holding power
- You work in tight vertical spaces
Skip if
- You need variable speed control
- You drill large holes over 1-7/16"
- You require high-speed precision work
Verdict: EUROBOOR ECO.36+ Magnetic Drill Press fits users drilling under steel beams who need strong magnetic holding power. It sacrifices speed versatility for a compact 6.5-inch profile.
Specifications side by side
| Spec | Hougen HMD900 Magnetic Drill | EUROBOOR Low Profile Magnetic Drill Press |
|---|---|---|
| Motor Power | not stated | 9.5A |
| Spindle Speed | not stated | 700 RPM (400 RPM under load) |
| Hole Capacity | 1.5" | 7/16" - 1-7/16" |
| Magnetic Force | not stated | 2645 lbs |
| Voltage | 115V | not stated |
| Configuration | Magnetic | Magnetic |
| Amperage | not stated | 5 A |
| Design | not stated | Low Profile |
| Dimensions | 11 × 6.75 × 15 inches | not stated |
| Weight | 27 pounds | not stated |
| Color | Multicolor | Black |
| Model | 0900101 | ECO.36+ |
Frequently asked questions
Which magnetic drill press is better for heavy steel work?
The Hougen HMD900 is the better choice for heavy steel tasks. It offers a 1.5-inch hole capacity, which exceeds the EUROBOOR ECO.36+ maximum of 1-7/16 inches. This larger capacity allows you to drill thicker metal plates with ease. The Hougen unit also weighs 27 pounds, providing stability during demanding industrial operations.
Is the EUROBOOR drill press suitable for tight spaces?
Yes, the EUROBOOR ECO.36+ is designed for tight spaces. It features a low profile design that fits under steel beams. This compact 6.5-inch profile makes it ideal for overhead or confined area drilling. The Hougen HMD900 is taller and wider, making it less suitable for restricted environments.
How do the dimensions of these magnetic drills compare?
The Hougen HMD900 measures 11 inches in length, 6.75 inches in width, and 15 inches in height. The EUROBOOR ECO.36+ has a lower profile, standing at 6.5 inches tall. The EUROBOOR unit is more compact overall, while the Hougen model is larger and heavier at 27 pounds.
What is the power source for these magnetic drills?
The Hougen HMD900 operates on 115V power. The EUROBOOR ECO.36+ draws 5 amps of current. Both units are electric magnetic drills designed for professional use. The Hougen model specifies its voltage, while the EUROBOOR model highlights its amperage draw for electrical planning.
Which drill press is lighter to carry?
The Hougen HMD900 weighs 27 pounds. The EUROBOOR ECO.36+ weight is not listed in the provided data. However, the EUROBOOR is described as having a low profile and compact design, which often suggests portability. You should check the specific weight of the EUROBOOR unit if portability is a primary concern.
Can I use these drills for vertical surface drilling?
Yes, both units are magnetic drill presses designed for vertical surfaces. The Hougen HMD900 is specifically noted for vertical surface drilling on heavy steel. The EUROBOOR ECO.36+ also uses magnetic configuration to hold firmly to steel, allowing for safe vertical and overhead drilling operations.
What is the model number for the Hougen drill press?
The model number for the Hougen HMD900 is 0900101. The EUROBOOR ECO.36+ model is identified as ECO.36+. These identifiers help you locate specific replacement parts or verify the exact configuration of the machines you are considering for your workshop.